4x Complete Innovative Red Anodized Savage Shocks

139.54€

Product may vary slightly from image representation.
  • Model:Sav-BB-RED
Live Stock Check: 0 units
Share This Product

These shocks are V2 and contain parts from our new 1/5th Baja Big Bore Shocks fully made by Innovative-RC.
These shocks are fully designed to be used with Innovative-RC LST Shock mounting kit for mounting the shocks onto the HPI savage (all Models).

Shock bodys also now have a ultra fine burnished mirror-like finish giving a tough,work-hardened surface finish as fine as 2 micro-inches (0.05 micrometers) translating to giving a silky smooth operation over the entire shock travel distance.

Starting with a large oversized shock body of 20mm giving a huge volume of oil followed by a 8mm high tensile steel shaft that is precision ground round for a perfect seal in all conditions as opposed to 4mm (RTR) these shocks are a big bore shock just like the LST1/LST2 shocks and contain an oil bleed hole located in the shock cap to allow for easy assembly and getting every last bit of air out of the shock when fully assembled.

No large shock shaft would be complete with out a full Umbrella / Oil seals to give the best possible oil seal, making leaks a thing of the past. we have also built other seals into the shock bottom cap to limit any dirt & sand entering into the shock seals from harsh environments meaning no expensive seal upgrades are needed.

The shock body contains a fully adjustable spring retaining ring for full adjustment of the shock spring to fine tune shock setup to any drivers needs and requirements when out bashing or racing on & off road.

All parts are made from high grade derlin while alll aluminium parts are made from high grade 6082-T6 and anodized to a hard durable finish.
Shock Shafts are a massive 8mm thick & made from high grade steel for long life when bashing.
Shocks are available in a black, clear/Silver & Blue anodized finish.

These shocks come fully complete and just need oil adding, we recommend an oil of around 35 ~ 40wt but this is down to the customers needs and area of use etc.

.:Over View:

  • Massive 8mm front shock shaft - ground round for a perfect sea - Surface finish: Better than 0.6 microns (25 micro inch)
     
  • Shock bodys also now have a ultra fine burnished mirror-like finish giving a tough,work-hardened surface finish
  • 4x Savage Big Bore shocks - pre assembled.

  • 4x Bottom rose joint balls for mounting.

  • Pre install Umbrella/Oil seals for leak free and long life shock operation.

  • Extra seal protection before oil/umbrella seal to stop sand and find dirt entering seals.

.:Needed & recommended Parts:.

  • Shock Oil - 57ml (2oz) ~ fills two and half shocks.

  • Shock Mounting kit for LST Shocks (depending on savage models)

  • Coustom Shock Socks available from us & groovy_gaiters

  • Aprox 140grams each
    33mm OD spring
    ~160mm Eye to Eye (center to center) Mount

.:Oil recommended:.
We find we do get asked this question quite often, please use the bellow as a guide line only, as we can not know your driving style and likes but we find it helps most people get started on there way to a set-up they like, also custom pistons can help in shock rebound rates (see shock parts for blank pistons and other piston types)

Silicone shock oil, recommend, 20-35wt front, 25-45wt rear. (~200CPS - 400CPS front, 280CPS - 650 CPS rear),

 

any questions please contact us.

Grabbed a set of these for my CEN Reeper after seeing someone on YouTube run them. Build quality is superb. Not too many options out there for the Reeper so I was happy everything went together well. All included hardware was solid and they mounted up easily. (I had to drill the mounts to fit the stock Reeper upper mounting screw size) The only thing I found difficult was the lower shock cup doesn't have a slot to fit around the piston so I had to fill and bleed with the spring on but it worked.

Rated by John
Your S & R Text. Could be a copy of what is in shipping.php, a precis of it, a link to it, etc. Whatever you decide you need...
Manufacturers
Share This Product
1 x M3x25mm Socket Cap Screw - BAG 101 x 2x Nitro Silicone Switch Cover - Futaba etc1 x M3x35 Socket head cap screws - bag 102 x Front Heavy Duty losi Shock Shaft - 8mm1 x Black Big Bore shock Spring Retainers - Aluminium1 x 500mm Servo Extention Lead(50cm/19.68") JR, Futaba, Hite2 x Front Thunder Tiger MT4 CVD Universal drive shaft set2 x 2x Top shock support brackets - Savage x2 x High response clutch set - Red Spring1 x M3 washers - Zinc plated bag 202 x M4x16 Socket head cap screws - bag 102 x Carb & Exhaust screws - 154822 x CVD inner Drive set Pins 5x22mm2 x Clutch Spring - Yellow1 x M2.5x6mm (For Engine Back/Cover plate) - Bag of 81 x 2 Bolt heavy duty Cylinder Gasket1 x Baja Shock Spring Retainer - Slotted1 x M3x3 Grub Set screw1 x Engine Clutch bottom spacer 6.5mm - 875711 x UHD CVD Shaft Front Center Losi 5ive - TLR252013 / LOSB32181 x 3x6x0.3 Steel Shim - Pack 101 x UHD Dgobone Drive Pin Set 1/4"x25mm1 x 1x Losi 8ight-T Diff Cup - Black1 x SuperSwitchHD - 1x1 x HPI Baja Brake Calliper - Blue Anodized4 x Baja Front Upper Brace Blue - 874811 x 3x Lightning Stadium (LSP) Diff Cup Case (B,F,C) - Silver1 x Front Big Bore Shocks - Losi 5ive Red1 x Baja Diff gear Drive pin - 965011 x RACE CVD Shaft Front or Rear Losi 5ive (2x) - B32161 x Rear Thunder Tiger MT4 CVD Universal drive shaft set1 x Piston Snap Ring Set1 x Baja Upper Front Arm Brace Upper Blue2 x IRC Hing Pins Rear Bottom V2 - 866351 x Savage Big Bore shock Socks - Black3 x FILTERED FUEL PICK UP CLUNK1 x RACE CVD Shaft Front Center Losi 5ive - TLR252013 / LOSB32181 x M2.5x10mm Socket Head Cap Screw - Bag of 101 x Brake plate spacer Blue - 874971 x HPI BAja Left Side Engine Mount Brace Black Anodized - 874891 x O-Ring Diff Cups - 5.5x2mm2 x M4x30 Countersunk Socket head cap screws - bag 101 x M4 Spring Washer Zinc plated - bag 201 x M3x8 Socket head cap screws - bag 101 x Shock O-Ring Kit1 x Holts Brake Cleaner1 x 4-40x1/2 Socket Head Cap Screw - Bag 102 x CVD Booted F/R stub Axle Losi 5IVE-T, MINI WRC (2x) - B32242 x Smart-Fly - Pin & Flag2 x Full X upgrade Kit3 x Front Axel - Thunder Tiger MT4 CVD Universal2 x M4x4 Grub Screws2 x 4x8x0.3 Steel Shim - Pack 103 x Baja Diff Cup side screws2 x DBXL Top shock cap Bush 5mm2 x Thunder Tiger Front/Rear outdrive3 x 4-40x3/8 Socket Head Cap Screw - Bag 102 x 90Deg PushFit 4mm tube M53 x 23mm Heavy Duty Wheel Hex - Left hand wheel hex bodies2 x RACE CVD Shaft Set Front or Rear Losi 5IVE-T (2x) - B32163 x 4-40x3/8 Button Head socket Screw - Bag 102 x RACE Outdrive F/R Axle Losi 5IVE-T, MINI WRC (2x) - B32122 x IRC BLACK MID rear big bore springs - Losi 5T1 x 300mm Servo Extention Lead(30cm/11.8") JR, Futaba, Hite1 x HPI Baja Right Side Engine Mount Brace Black Anodized - 874901 x Rear Axel - Thunder Tiger MT4 CVD Universal1 x M4x12 Socket head cap screws - bag 101 x Baja Bush Set - BLUE1 x M3 Nylock nut bag of 201 x HPI Baja Rear Brace 4mm Black Anodized - 874881 x Savage Shock Bottom End Cap1 x 23mm Heavy Duty wheel hex - 2x Left Hand Nuts1 x M4x10 Socket head cap screws - bag 101 x Baja Diff o-rings - bag101 x Ultra Heavy Duty Front Center Dogbone - 78mm1 x M4x30 Socket head cap screws - bag 101 x Baja Shock Spring Retainer - LST1 x Big Bore Shock 4 Hole Piston DUAL Rate1 x M3 Captive Nuts / T Nuts - Bag101 x Petrol Fuel Tube pipe ID 3.2mm OD4.9mm Yellow - 1M long1 x 2x 3mm Top Mount Brackets1 x Front - Antiroll Bar brace2 x V2 Plated Savage + MCD V4 Heavy Duty Baja Shock Shaft - 8mm1 x 4x Stainles SHOCK BUSHINGS / Standoffs With Screws1 x Losi 5T 5B Shock Towers Bash - Rear BLACK1 x Futaba type sliding charing switch1 x CY Flywheel / Fan Cover1 x HPI Baja wheel drive pin 5x24- 965041 x X Upgrade Kit
Reviews
Skid Plate for Exstended 1inch back, 6mm Front TVPs
Skid Plate for Exstended 1inch back, 6mm Front TVPs
13.95€

got this last week and fits perfect and holds all the tvps n...